Glason WonderBond™ W.B.
WonderBond™ W.B. is a water thinned surface coating designed to provide a durable and chemical resistant trafficable coating for floors. The special blend of resins in WonderBond™ W.B. are designed to resist staining from fat, sump oil, grease, petrol and acids without harming the finish.
The product will mimic the contours of the substrate rather than giving a high film build and can therefore not be considered a 'wet look'. This mimic effect allows effective application on smooth surface, concrete in factories. WonderBond™ WB has also been used as an excellent base coat for epoxy floor finishes as well as conventional paint systems.
The product has been designed to bind powdering surfaces and has excellent adhesion.
As with all surface coatings, the system is sacrificial and must therefore be re-coated at regular intervals, however, it has a marked superiority over traditional solvent systems as shown in the tests below.
Note: For these tests to be fair, the WonderBond™ W.B. had to be watered down to match the solids content of the solvent based competitor.
| TEST | WB SEAL |
Solvent |
Urethane |
|---|---|---|---|
| Leveling: - Concrete - VA Tile |
Excellent Good |
Excellent Fair |
Very Good Fair |
| Adhesion: - Solid C - Clean C |
Excellent Excellent |
Poor/Fair Very Good |
Poor/Fair Very Good |
| Water Resistance: - Penetration - Film Damage |
Very Good None |
Very Good None |
Very Good None |
| Petrol Resistance: - Penetration - Chemical Resist |
Good Very Good |
Good Very Good |
Good Very Good |
| Hydrochloric Acid: - Penetration - Chemical Resist |
Very Good Good |
Very Good Good |
Very Good Good |
| Oil Resistance: - Penetration - Chemical Resist |
Excellent Excellent |
Excellent Excellent |
Excellent Excellent |
| Detergent Resist | Excellent | Excellent | Excellent |
| Abrasion Resist | Fair | Fair | Fair |
| Black Tyre Resist | Fair | Good | Good |
| Scuff Resist | Good | Very Good | Very Good |
DIRECTIONS
SURFACE PREPARATION:
1. Surface should be clean, dry and free of any stains or contaminants that will show through or damage the coating.
2. Mould, fungus, cement and grout residues should be removed with
Glason Mould & Leaf Stain Remover
Mould & Leaf Stain Remover is a chlorinated concentrate containing a range of specialised surfactants and wetting agents designed to prevent spore spread and improve killing power.
Ideal for: Concrete, pavers, pebble crete, color bond, timber, stencil crete, retaining walls, timber, pavers, signage, etc.
Clean up: Wash off with water.
Sizes: 5 litre - 20 litre
Coverage: 15 to 20 sq metres
taking care to hose off all residues.
Glason KN Clean
K.N. Clean is a highly concentrated detergent manufactured and supplied in powder form to provide the user with superior cleaning at an economical price.
When used as directed, K.N. Clean will effectively remove most soiling caused by cooking oils and fats as well as staining in high traffic pedestrian areas without leaving a slippery residue.
K.N. Clean is non residual and biodegradable when tested as per Australian Standard AS1792.
K.N. Clean is safe and contains no caustics or acids which means no more caustic burns for you or your staff.
Ideal for: Kitchens, bathrooms, garage, toilets, offices, workshops and general areas.
Clean up: Rinse well with water
Sizes: 75 gram - 1.5 kg - 6 kg - 12 kg
Cost Effective: 750 gm of KN Clean = 25 litres of concentrated detergent. That means 750 gm = 500 litres of ready to use cleaner.
or
Hard Surface Cleaner
Hard Surface Cleaner is a potent blend of active compounds that are designed to attack and allow easy removal of staining such as grease, rubber, oil and fat dirt, grime, rubber marks, scuff marks on pavers or floors and bench tops.
Ideal for: Tiles, driveways, tyre marks, pool surrounds, pavers, stone, timber, vinyl, laminex and any hard surface.
Clean up: Rinse well with water.
Sizes: 1 litre - 5 litre - 15 litre - 25 litre.
is recommended on Vinyl or other similar surfaces. Allow to dry thoroughly before proceeding
3. All loose material must be removed to ensure a stable surface.
4. Areas that retain old coatings will require more prepatory work. Should any doubt exist as to the preparation necessary on a particular surface, please contact the Glason distributor in your state.
RATIO:
Use neat.
APPLICATION:
Brush, short nap roller, knapsack spray, airless spray or nylon broom. SHAKE BEFORE USE.
COVERAGE:
12 square metres per litre per coat depending upon absorption.
CLEAN UP:
Immediately was all tools in warm water and detergent.
DRYING & RE-COAT TIMES:
Touch dry in 20 minutes. Re-coat in 2 hours. Walk on in 1 hour. Heavy traffic after 24 hours.
DO NOT USE BELOW 10°CELCIUS. DO NOT ALLOW PRODUCT TO FREEZE.